VScom 200I-SI UPCI
Características destacadas
- Universal PCI 3.3 / 5.0V
- 2x RS232, RS422/485
- RS485 ART (Automatic Receive Transmit Control)
- RS485 in 3 operation modes
- optical isolation, surge protection (also in RS232)
- PCI Plug and Play
- IRQ Interrupt sharing, only one Interrupt per card
- Drivers for Windows 95 to 7/2008 R2
- Software compatibel with DOS, Windows 3.11, OS/2, Linux and div. Unix
- Compact board (half-size)
- Hardware flow control
- Built-in termination resistors
Descripción
The VScom 200I-SI uPCI is designed for RS232, RS422/485 industrial communication. It supports 2 independent RS232, RS422 or RS485 ports. Each port can be configured separate.
Available modes : RS232, RS422 fullduplex
RS485 full duplex (4 wire)
RS485 half duplex (2 wire) with and without echo.
In RS485 modes applications enable transmission by simply sending data.
This is done by ART (Automatic Receive Transmit control) intelligence.
The Transmitter is disabled exactly with the end of the last character sent. No modification is necessary in programs.
In addition, hardware flow control and built-in termination resistors guarantee data integrity.
Optical isolation and surge protection ara also available for RS232 Signals to deliver high reliability.
All of these features make VScom 200I - SI uPCI suitable for harsh industrial applications.
Optical isolated RS232 presents 200I-SI as a choice for medical environment.
Read the News Article…
Application | |
Multiport data acquisition Factory automation Remote serial device control | Industrial control Embedded industrial machine SCADA |
Part Number | 4439 |
Especificaciones Tecnicas
Hardware | |
I/O controller | 2x 16C550C or compatible, each with 16 bytes Tx/Rx FIFO |
Connector type | Male DB9 |
Interface | |
Bus interface | PCI version 2.1 (32bit) Universal PCI 3.3V / 5.0V |
Serial interface | RS232, RS422 / 485 |
No. of ports | 2 |
Signals | RS232 Tx, Rx, CTS, RTS also with optical isolation and surge protectionRS422 TxD+/-, RxD+/-, RTS+/-, CTS+/-, GNDRS485 Data+/-, GND |
RS485 data control | ART (Automatic Receive Transmit control) |
Built-in termination resistor | RS422 120 OhmRS485 120 Ohm, jumper enable / disable |
Performance | |
Speed | up to 921.6Kbps |
Max. no. of ports | Unlimited |
Configuration | |
Parity | None, even, odd, space, mark |
Data bits | 5, 6, 7, 8 |
Stop bits | 1, 1.5, 2 |
IRQ | Assigned by System |
I/O address | Assigned by System |
Available modes | |
RS232 | full duplex |
RS422 | full duplex |
RS485 | 4 wire , full duplex |
RS485 | 2 wire, half duplex, with echo |
RS485 | 2 wire, half duplex, without echo |
Power and Environment | |
Power requirement | 430mA max.(+5V) |
Operation temp. | 0°C - 55°C |
Dimension | 120mm x 100mm |
Operating Systems | |
Windows 2000 up to 7 | VScom high performance serial driver, x86 and x64 Editions |
Server 2000 to 2008 R2 | VScom high performance serial driver, x86 and x64 Editions |
Windows NT 4.0 | VScom high performance serial drivercontrol panel applet |
Windows 95, 98, SE, ME | VScom high performance serial driver |
DOS | virtuell address driver and compatibility toolsreal DOS Com port emulation |
OS/2 | Supported by COM16 driver in recent system releasesThird party serial driver SIO.SYS available |
Linux | Kernel 2.6 and up: built-in supportPrevious kernel: VScom high performance real tty driver |
div.UNIX | configuration instructions |
Referencia | Descripcion |
---|---|
4439 | 4439 |
Documentacion | VScom 200I-SI UPCI Datasheet |