Cod: HMS-EN2SE-R - Nombre: EtherNet/IP to Serial Linking Device

Anybus
serial-to-ethernet-ip-linkingdevice

EtherNet/IP to Serial Linking Device

The Linking Device performs an intelligent protocol conversion and presents the serial data to the Logix PLC as easily processed I/O data. This offloads your Logix PLC from working with additional calculations. 

Características destacadas

  • Enables the retro-fitting of existing serial RS232/422/485 devices with Logix PLCs with EtherNet/IP
  • No hardware or software changes, for the connected device
  • Connects up to 31 serial nodes via RS-485
  • Up to 500 bytes of Input data and 496 bytes of Output data
  • Speed up configuration through a seamless integration with Studio 5000 Logix Designer
  • Compatible with all ControlLogix and CompactLogix PLCs supporting EtherNet/IP
  • Easy to setup with Custom Add On Profile with no programming required!
  • Everything configured through Studio5000®, no 3rd party software or licenses needed
Dimensions  (L•W•H) 120 x 75 x 25mm or 4,72 x 2,95 x 1,06"
Weight 150g, 0,33lb
Operating temperature0 to +55 °C  or  0 to +131 °F 
Storage temperature -40 to +85 °C  or  -40 to +185 °F 
Power supply 24 VDC +/- 10%
Current consumption max. 300mA (Typical 100mA)
Enclosure materialPC ABS, UL94
Installation position  Vertical
Galvanic isolation YES, on both BUS/Ethernet side
Mechanical rating IP20, NEMA rating 1
MountingDIN-rail (EN 50022 standard) or Wall mount
Serial baudrate1,2-57,6 kbit/s
EtherNet/IP baudrate 10/100 Mbit/s autodetect 
EtherNet/IP connector 2x RJ45
EtherNet/IP address Any valid IP address can be used 
TCP/IP settings Configurable via web-page, configuration tool, DHCP/ARP or via DIP switches 
Certifications CE, CULUS, ATEX/Haz.Loc  (PENDING)

Connect any RS-232/422/485 serial device to ControlLogix® or CompactLogix® controllers with an EtherNet/IP interface.

The Linking Device performs an intelligent protocol conversion and presents the serial data to the Logix PLC as easily processed I/O data. This offloads your Logix PLC from working with additional calculations. 

CONVERT ALMOST ANY TYPE OF SERIAL PROTOCOL

The Linking Device is capable of converting almost any type of serial protocol such as Modbus RTU, DF1, ASCII, or any other type of proprietary; Request/Response or Produce/Consume protocol.

Seamless integration with Studio 5000

With its unique Studio 5000® Logix designer integration, everything is accessible from within Studio 5000, including then serial network configuration. No extra 3rd-party software, licenses or programming required.

Connect, configure, done

EtherNet/IP Linking Devices are configured using a Custom Add On Profile for Studio 5000 Logix Designer. This dynamically generates data structures for each device connected. No ladder logic files (add on instructions) needed.

Furthermore, it also supports automatic generation of named and structured Studio 5000 controller tags, which eliminates the need to create alias tags

Serial protocol configuration features

  • Selectable RS-232/422/485 interface
  • Modbus-RTU Master functionality with pre-defined Modbus-RTU configuration wizard
  • DF1 Master functionality with selectable pre-loaded DF1 commands
  • Ability to configure ASCII or vendor specific protocols (Request/Response or Produce/Consume via a visual byte-based frame building)
  • Ability to make popular checksum calaculations 
  • In-built Line Listener to analyze serial telegrams on the sub-network (accessable via Studio5000)

EtherNet/IP interface features

  • EtherNet/IP CONFORMANCE TESTED™ by ODVA
  • EtherNet/IP Adapter Level 2 and Level 3  I/O Server CIP
  • Max 500 bytes Input and 496 bytes Output data
  • 10/100Mbit operation in full or half-duplex
  • Device Level Ring (DLR) functionality available (announce-based ring participant)
  • Per-user security framework
  • Quality of Service (QoS) available
  • TCP/IP settings can be configurable with web-page, Configuration Tool, DHCP or ARP
  • Integrated switch allowing for a daisy-chain topology
  • Dual RJ-45 ports available simultaneously
     
Order Code  HMS-EN2SE-R               
Included componentsHMS-EN2SE-R Linking Device, Installation guide, D-sub connector with screw terminals for sub-network. (Power supply not included) 
Optional Accessories USB-RS-232 configuration adapter (Order Code 019570) 
Guarantee 3 years  
Bienvenido a ER-Soft.
ER-Soft con la ley orgánica de protección de datos
Política de cookies.
Utilizamos cookies propias y de terceros para mejorar nuestros servicios y mostrarle publicidad relacionada con sus preferencias mediante el análisis de sus hábitos de navegación.
Si continúa navegando, consideramos que acepta su uso.
Más información pulsando aquí
X

¿Necesitas ayuda? Click

ayuda ER-Soft
X
Consulta a ER-Soft. *

 

*

 

* *Campos obligatorios.




*Al enviar el formulario consideramos que esta de acuerdo, con nuestra política de datos. Ver política de datos
X