Anybus X-gateway – PROFIBUS Slave - J1939
Características destacadas
- Monitor and control data on a J1939 heavy duty vehicle network from PROFIBUS PLC system or device
- Typical applications: Electric Power Generation, Oil & Gas, Marine, Military, Heavy Duty Vehicles, Any Diesel Engine based system supporting J1939
- Max 500 bytes of I/O data in each direction
- Easy configuration via the included BWConfig Windows Software. No programming required
- Robust aluminum stand-alone housing
- Global free technical support and consultancy
Descripción
The Anybus X-gateway J1939 Gateway provides connectivity between a PROFIBUS network and a J1939 Heavy Duty vehicle (CAN) network. The X-gateway appears as a PROFIBUS-DP Slave device allowing a PROFIBUS Master to read or write data from the J1939 network.
EASY CONFIGURATION - NO PROGRAMMING REQUIRED!
HMS provides the X-gateway with a free Windows based configuration tool (BWConfig). This PC based software allows the user to map J1939 parameter (PGN) data into a range of memory addressable through the Anybus X-gateway PROFIBUS-DP interface.
Configuration of the X-gateway is simple using BWConfig and consists of setting up an I/O table containing selected J1939 PGNs and the rate that each will be read or written from the J1939 network. BWConfig will then automatically map the I/O table to a range of addresses accessible from the X-gateway PROFIBUS interface.
The configuration is downloaded from the PC to the Anybus X-gateway via an RS232 connection and is saved in FLASH memory.
PROFIBUS Slave interface
PROFIBUS Slave settings can be made either via on-board switches, or by importing the provided .GSD file into engineering tool of the controlling PLC.
- Complete PROFIBUS-DP Slave functionality according to extensions of EN 50170
- Baudrate detection up to 9-12Mbit/s
- 400 bytes total combined Input and Output table size including any status data and command registers
- Cyclic I/O data transmission
- Device diagnostic message transmission
- PROFIBUS slave settings via on-board switches or vis .GSD file
- 1x D-sub 9-pin female PROFIBUS connector
J1939 interface
- SAE J1939 network interface with a unique network address in accordance to the J1939-81 specification
- Max 496 bytes of I/O Input data and 492 bytes of I/O Output Data
- Up to 120 PGN's monitored by Input data points
- Up to 100 PGN's transmitted by Output data points
- Supports J1939 network baud rates of 250K and 500K
- Transmission and reception of all types of fixed-length J1939 messages, including PDU1, PDU2, broadcast and destination specific
- Monitoring of DM1 (active diagnostics) and DM2 (previously active diagnostics) messages
- Complete network address management including address claim, protection, and yield on higher priority conflict
- Network address can be self-configurable over a range of addresses
- J1939 Transport Protocol for transmission and reception of large messages (9 - 1785 bytes). Both connection based (RTS/CTS) and broadcast (BAM) are supported
- Configurable CAN bus-off reset option will reset the network interface and attempt to return to online when a CAN bus-off condition is detected
- 1x 5-pole 5.08 mm Phoenix pluggable screw connector for J1939
Order Code | AB7615 |
Price group | A |
Included components | Resource CD with "BWConfig" Windows software, Manuals, RS-232 configuration cable, Installation Guide, 5-pole 5.08 mm Phoenix pluggable screw J1939 connector 2-pole 5.08 mm Phoenix pluggable screw connector (Power supply not included) |
Order information USA & Canada | Please contact us-sales@anybus.com +1 312 829 0601 for ordering information within the USA and Canada |
Guarantee | 3 years |
Especificaciones Tecnicas
Dimensions (L•W•D) | 126 x 110 x 42mm or 4,96 x 4,33 x 1,65" |
Weight | 500g or 1,10 lbs |
Operating temperature | 0 to +70 °C or +32 to +158 °F |
Storage temperature | -25 to +85 °C or -13 to +185 °F |
Power supply | 24 VDC +/- 20% via 2-pole 5.08 mm Phoenix pluggable screw connector |
Current consumption | max. 300mA (Typical 200mA) |
Enclosure material | Aluminium |
Installation position | Vertical |
Galvanic isolation | YES, on both BUS/Ethernet side |
Mechanical rating | IP20, NEMA rating 1 |
Mounting | DIN-rail (EN 50022 standard) |
Configuration | via 9-pin DSUB RS-232 port with the included BWConfig Windows software |
Certifications | CE, CULUS |
Referencia | Descripcion |
---|---|
AB7615 | Anybus X-gateway – PROFIBUS Slave - J1939 |
Documentacion | Firmware Download Anybus X-gateway Classic |
Documentacion | Installation Guide Anybus X-gateway |
Documentacion | User Manual ABX |
Documentacion | User Manual |
Descargas | Datasheet |
Descargas | EU Declaration Of Conformity and ATEX Conformance Certificate |
Descargas | Firmware Download Tp |
Descargas | GSD File For Profibus |
Descargas | J1939 Application Notes And Configurations |
Descargas | NetTool for Profibus (Demo max 2 slaves) |