Soluciones Wireless industrial Anybus
Anybus

Soluciones Wireless industrial Anybus


Soluciones Wireless industrial Anybus


Anybus
 Anybus Wireless Router LTE - Global

Código: AWB5221

The Anybus Wireless Routers are ideal to provide your industry with high-speed LTE connectivity. Advanced routing functionality allows you to segment your network and protect mission critical data. An extensive range of redundancy technologies ensures uni
  • HIGH THROUGHPUT WIRELESS PERFORMANCE
  • LTE Cat.4 modem 2x2 MIMO, 150 Mbit/s downlink and 50 Mbit/s uplink
  • 4G/3G/2G full cellular network compatibility
  • ETHERNET ROUTING SWITCH
  • 8 Fast Ethernet LAN ports
  • 1 Gigabit Ethernet WAN port
  • IEEE 802.1p QoS/802.1Q VLAN priority tagging
  • RIPv2
  • Traffic control
  • ENHANCED SECURITY AND REDUNDANCY FOR CRITICAL APPLICATIONS
  • Firewall for traffic classification, port forwarding
  • VRRP (Virtual Routing Redundancy Protocol).
  • GRE (Generic Routing Encapsulation RFC2784)
  • Supports NAT, DMZ for LAN protection
  • Supports IPsec, OpenVPN and L2TP for secure connection
  • RUGGED DESIGN
  • Effective heat dissipation design for operating in -40 to 75°C environments
  • Railway EMC: EN50121-4 compliance
  • IEC61000-6-2/IEC61000-6-4 heavy industrial EMC
  • Vehicle: E-mark compliance
  • Radio: RED for CE Marking
  • Emission: FCC part 15 B Class A
  • MANAGEMENT FEATURES
  • Various configuration paths, including WebGUI, CLI and SNMP
  • Diagnostic tools, including LED, Ping/Traceroute, SNMP Trap, E-mail alert and Syslog
  • External backup/restore, Firmware update
Ethernet ports

       LAN: 8 x 100 Mbit/s RJ45, auto negotiation, auto MDI/MDI-X 

       WAN: 1 x 1 Gbit/s RJ45, auto negotiation, auto MDI/MDI-X

USB
       1 x USB type A
Operating temp.
      -40oC-75oC, 5-95 % non-condensing
 Cellular standards

       LTE cat.4 2x2 MIMO, 4G/3G/2G fall back

       LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/B19/B20/B25/B26/B28

       LTE-TDD: B38/B39/B40/B41

       WCDMA: B1/B2/B4/B5/B6/B8/B19

Data speeds

       LTE-FDD: DL: max. 150 Mbit/s, UL: max. 50 Mbit/s  

       LTE-TDD: DL: max. 130 Mbit/s, UL: max. 35 Mbit/s           

       HSPA: DL: max. 42 Mbit/s, UL: max. 5.76 Mbit/s  

       EDGE: DL: max. 236.8 kbit/s, UL: max. 236.8 kbit/s

       GPRS: DL: max. 85.6 kbit/s, UL: max. 85.6 kbit/s

 GNSS

       GPS

       GLONASS

       Galileo

       BeiDou

Power

        8-32 VDC (max. 4.8 W)  

        4-pin removable terminal block connector  

        2-pin for power input  

        2-pin for dry relay output (max 0.5 A/24 VDC)

Weight
        1 400 g
Housing material         Steel/aluminum
Ingress protection         IP31
Dimensions         200 x 126 x 51 mm (without DIN rail clip)
Mounting         Panel mount or DIN rail mount (bracket included)
Configuration          CGI WebGUI, SSH, Telnet, SNMP 

Anybus Wireless Router LTE - Global

Anybus
 https://www.anybus.com/products/wireless-products/wireless-infrastructure/detail/anybus-wireless-router-wlan?ordercode=AWB5121

Código: AWB5121

The Anybus Wireless Routers are ideal to provide your industry with high-speed WLAN connectivity. Advanced routing functionality allows you to segment your network and protect mission critical data. An extensive range of redundancy technologies ensures un
  • HIGH THROUGHPUT WIRELESS PERFORMANCE
  • Dual radio, 2.4 GHz or 5 GHz WLAN for local coverage, up to 866 Mbit/s
  • IEEE 802.11ac compliant & backward compatible with 802.11a/b/g/n
  • ETHERNET ROUTING SWITCH
  • 8 Fast Ethernet LAN ports
  • 1 Gigabit Ethernet WAN port
  • IEEE 802.1p QoS/802.1Q VLAN priority tagging
  • RIPv2
  • Traffic control
  • ENHANCED SECURITY AND REDUNDANCY FOR CRITICAL APPLICATIONS
  • Firewall for traffic classification, port forwarding
  • VRRP (Virtual Routing Redundancy Protocol).
  • GRE (Generic Routing Encapsulation RFC2784)
  • Supports NAT, DMZ for LAN protection
  • Supports IPsec, OpenVPN and L2TP for secure connection
  • RUGGED DESIGN
  • Effective heat dissipation design for operating in -40 to 75°C environments
  • Railway EMC: EN50121-4 compliance
  • IEC61000-6-2/IEC61000-6-4 heavy industrial EMC
  • Vehicle: E-mark compliance
  • Radio RED for CE Marking
  • Emission: FCC part 15 B Class A
  • MANAGEMENT FEATURES
  • Various configuration paths, including WebGUI, CLI and SNMP
  • Diagnostic tools, including LED, Ping/Traceroute, SNMP Trap, E-mail Alert and Syslog
  • External backup/restore, Firmware update
Ethernet ports

       LAN: 8 x 100 Mbit/s RJ45, auto negotiation, auto MDI/MDI-X 

       WAN: 1 x 1 Gbit/s RJ45, auto negotiation, auto MDI/MDI-X

USB
       1 x USB type A
Operating temp.
      -40oC-75oC, 5-95 % non-condensing
Data speeds

      802.11ac: MCS 0-9, max. 866 Mbit/s  

      802.11b: 11 Mbit/s           

      802.11a/g: 54 Mbit/s  

      802.11n: MCS 0-15, max. 300 Mbit/s

Power

      8-32 VDC (max. 4.8 W)  

      4-pin removable terminal block connector  

      2-pin for power input  

      2-pin for dry relay output (max 0.5 A/24 VDC)

Weight
      1 400 g
Housing material       Steel/aluminum
Ingress protection       IP31
Dimensions       200 x 126 x 51 mm (without DIN rail clip)
Mounting       Panel mount or DIN rail mount (bracket included)
Configuration        CGI WebGUI, SSH, Telnet, SNMP 

Anybus Wireless Router WLAN

Anybus
 Anybus WLAN Access Point IP30

Código: AWB4001

The Anybus Wireless LAN Access Point IP30 is a powerful industrial-grade infrastructure device that can connect several Wireless LAN clients over long distances.
  • Features and Benefits
  • Allows for the setup of a Wireless infrastructure by connecting several WLAN clients over long distances
  • Ideal for collecting data from nearlying machinery equipped with Anybus Wireless Bolts or Bridges
  • Range up to 400 meters
  • Rugged design for indoor usage with IP30 class housing
  • Connectsa high number of clients
  • Easy configuration via a web-based interface
  • Wireless LAN interface supports up to 300 Mbps link speed
  • Supports AP/Bridge/Repeater/AP-Client Mode
  • Diagnostics: Event Warning by Syslog, Email, SNMP Trap, Relay outputs
  • WLAN (WIFI) Interface
  • 2.4GHz or 5GHz frequency
  • Gigabit Ethernet connection with dual ports 10/100/1000 Base-T(X) Ports in RJ45
  • Digital Inputs and Digital Outputs included for network and application diagnostics
  • Conforms to IEEE802.11 a/b/g/n specification
  • Operates as AP/Client/Bridge /AP-Client Mode
  • Connects a high number of clients
  • Throughput: IEE802.11b: 11 Mbps, IEE802.11a/g: 54 Mbps, IEE802.11n: 300 Mbps
  • Max Range: 400 meters
  • Max 17 dBm RF output power
Technical specifications
Wireless comm. WLAN 2.4GHz or  5GHz
Dimensions (WxHxD) 74.3  x 153.6  x 109.2 mm
Weight  1.11 kg
Operating temperature -25 to +70 °C  or -13 to +158 °F 
(Storage temp: -40 to +85 °C or -40 to +185 °F )
Antenna/RF output 2x External (RP SMA) -  17 dBm max 
Power supply  Dual DC inputs. 12~48VDC on 6-pin terminal block, Reverse polarity protection, 7.5 Watts.
Ethernet interface
2 LAN ports RJ45 10/100/1000 Base-T(X) Ports Auto MDI/ MDIX — 10/100 /1000 Base-T(X) 
Enclosure material Metal
Mechanical rating  IP30
Mounting DIN-rail or wall-mount (included)
Max range   400 meters
Configuration  Included web interface
PoE (P.D) support None


CERTIFICATIONS
 
Europe CE/RED 
USA 

FCC Part 15, CISPR (EN55022) class A EMS IEC61000-4-2 (ESD), IEC61000-4-3 (RS), IEC61000-4-4 (EFT), IEC61000-4-5 (Surge), IEC61000-4-6 (CS), IEC61000-4-8, IEC61000-4-11
Safety EN60950-1
UL 61010-2-201 / UL file E214107

WLAN Security 

WEP: (64-bit, 128-bit key supported) WPA/WPA2 :802.11i (WEP and AES encryption) WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported

Anybus WLAN Access Point IP30

Anybus
 Anybus WLAN Access Point IP67

Código: AWB4003

The Anybus Wireless LAN Access Point IP67 is a powerful industrial-grade infrastructure device that can connect several Wireless LAN clients over long distances.
  • Features and Benefits
  • Allows for the setup of a Wireless infrastructure by connecting several WLAN clients over long distances
  • Gigabit Ethernet connection with dual ports 10/100/1000 Base-T(X) Ports in RJ45
  • Ideal for collecting data from nearlying machinery equipped with Anybus Wireless Bolts or Bridges
  • Range up to 400 meters
  • Rugged wall-mounted IP67 class design (waterproof), ideal for either indoor or outdoor usage
  • Connects a high number of clients
  • Easy configuration via a web-based interface
  • Wireless LAN interface supports up to 300Mbps link speed
  • Supports AP/Bridge/Repeater/AP-Client Mode
  • Diagnostics: Event Warning by Syslog, Email, SNMP Trap, Relay outputs
  • WLAN (WIFI) Interface
  • 2.4GHz or 5GHz frequency
  • Conforms to IEEE802.11 a/b/g/n specification
  • Operates as AP/Client/Bridge /AP-Client Mode
  • Connects a high number of clients via WLAN
  • Throughput: IEE802.11b: 11 Mbps, IEE802.11a/g: 54 Mbps, IEE802.11n: 300 Mbps
  • Max Range: 400 meters
  • Max 17 dBm RF output power
Technical specifications
Wireless comm. WLAN 2.4GHz or 5GHz 
Dimensions (WxHxD) 310  x 87  x 310 mm
Weight  2.56 kg
Operating temperature -25 to +70 °C  or -13 to +158 °F 
(Storage temp: -40 to +85 °C or -40 to +185 °F )
Antenna/RF output 2x External  (N-Type) -  17 dBm max
Power supply  Dual Power Inputs. 12~48 VDC, 9 W, Power over Ethernet IEEE 802.3af.
Ethernet interface 1 LAN port M12 8-pin A-coding, 10/100/1000Base-T(X) Auto MDI/MDIX
Enclosure material Metal
Mechanical rating  IP67
Mounting Wall mount or pillar mount (included)
Max range   400 meters
Configuration  Included web interface
PoE (P.D) support Yes according to IEEE 802.3af Power Device specification


CERTIFICATIONS
 
Europe CE/RED 
USA 

FCC Part 15, CISPR (EN55022) class A EMS IEC61000-4-2 (ESD), IEC61000-4-3 (RS), IEC61000-4-4 (EFT), IEC61000-4-5 (Surge), IEC61000-4-6 (CS), IEC61000-4-8, IEC61000-4-11
Safety EN60950-1
Cooling EN60068-2-1
Dry Heat EN60068-2-2
UL 62368/UL 60950/UL file E466303

WLAN Security 

WEP: (64-bit, 128-bit key supported) WPA/WPA2 :802.11i (WEP and AES encryption) WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported

Anybus WLAN Access Point IP67 (AWB4004 (USA version) )

Anybus
 ethernet-bluetooth

Código: 023140

Anybus® Wireless Bridge Ethernet - Bluetooth provides a proven wireless connection between Industrial Ethernet installations. It acts as a cable replacement gateway and is ideal for communication through hazardous areas, hard-to-reach locations or with mo
  • Use with point-to-point wireless Industrial Ethernet installations through hazardous or hard-to-reach locations
  • Eliminates the need for expensive or maintenance-heavy cabling
  • Bridges TCP/IP Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP and PROFINET
  • Unique method to handle interference disturbances without consequences to the Bluetooth conformity or the interoperability with other devices
  • Effective range of up to 300 meters
  • Easy configuration via push button or web interface
  • Advanced configuration with AT commands
  • Up to seven wireless bridges can be used in a Wireless Network Platform (WNP)
  • Conforms to wireless standards used in Europe, USA, Canada and Japan
  • Rugged IP65 rated industrial design
Version Ethernet - Bluetooth Ethernet Access Point - Bluetooth Serial - Bluetooth
Dimensions  (L•W•H)91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"76 x 85 x 35mm 2,99 x 3,34 x 1,38"
Weight 120g or 0,26 lbs130g or 0,30 lbs 190g or 0,42 lbs
Operating temperature-30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F -30 to +85 °C -22 to +185 °F 
Output Power 13 dBm20 dBm 13 dBm
Power supply 9-30 VDC  9-30 VDC 8-30 VDC 
Power consumption min. 35mA at 30V (43mA average at 30V) min. 35mA at 30V (43mA average at 30V) min. 9mA at 30V (20mA average at 30V) 
Enclosure materialPlasticPlastic Metal
Mechanical rating IP65IP65IP65
MountingScrew holes for wall mountingScrew holes for wall mountingScrew holes for wall mounting
Max Range  300 meters 300 meters300 meters
Antenna/Connector Internal / NoExternal / Yes (RPSMA)External / Yes (RPSMA)
ConnectorsM12 (Ethernet and Power)M12 (Ethernet and Power) Male DSUB (Serial) Binder 712 (Power)
CERTIFICATIONS    
EuropeETSI R&TTE ETSI R&TTE ETSI R&TTE 
USA CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval
CanadaICC RSS ICC RSS ICC RSS 
JapanMIC - formerly TELEC MIC - formerly TELEC MIC - formerly TELEC
UL-Haz.Loc cUL Class 1 Div 2 cUL Class 1 Div 2-
Security Simple pairing Simple pairing WEP64, WEP128, WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP, EAP-TLS, 802.11i 
Medical Qualification --IEC 60601-1-2 

Anybus Wireless Bridge - Ethernet - Bluetooth

Anybus
 bluetooth-accesspoint

Código: 024130

Anybus® Wireless Bridge Ethernet Bluetooth Access Point is a rugged dual-mode Bluetooth (Bluetooth Smart Ready) access point with Bluetooth low energy gateway functionality. It allows up to seven Bluetooth devices to connect to the 10/100 Base-T Ethernet
  • Connects up to 7 Bluetooth devices to an Ethernet network
  • Eliminates the need for expensive or maintenance-heavy cabling
  • Connects TCP/IP Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP and specific optimization for PROFINET
  • Features a Low Emission Mode®: Prevents disrupting other 2.4GHz radios
  • Effective range of up to 300m
  • Easy configuration via push button or web interface
  • Advanced configuration with AT commands
  • Conforms to wireless standards used in Europe, USA, Canada and Japan
  • Rugged IP65 rated industrial design with choice of Antennas and accessories
Version Ethernet - Bluetooth Ethernet Access Point - Bluetooth Serial - Bluetooth
Dimensions  (L•W•H)91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"76 x 85 x 35mm 2,99 x 3,34 x 1,38"
Weight 120g or 0,26 lbs130g or 0,30 lbs 190g or 0,42 lbs
Operating temperature-30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F -30 to +85 °C -22 to +185 °F 
Output Power 13 dBm20 dBm 13 dBm
Power supply 9-30 VDC  9-30 VDC 8-30 VDC 
Power consumption min. 35mA at 30V (43mA average at 30V) min. 35mA at 30V (43mA average at 30V) min. 9mA at 30V (20mA average at 30V) 
Enclosure materialPlasticPlastic Metal
Mechanical rating IP65IP65IP65
MountingScrew holes for wall mountingScrew holes for wall mountingScrew holes for wall mounting
Max Range  300 meters 300 meters300 meters
Antenna/Connector Internal / NoExternal / Yes (RPSMA)External / Yes (RPSMA)
ConnectorsM12 (Ethernet and Power)M12 (Ethernet and Power) Male DSUB (Serial) Binder 712 (Power)
CERTIFICATIONS    
EuropeETSI R&TTE ETSI R&TTE ETSI R&TTE 
USA CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval
CanadaICC RSS ICC RSS ICC RSS 
JapanMIC - formerly TELEC MIC - formerly TELEC MIC - formerly TELEC
UL-Haz.Loc cUL Class 1 Div 2 cUL Class 1 Div 2-
Security Simple pairing Simple pairing WEP64, WEP128, WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP, EAP-TLS, 802.11i 
Medical Qualification --IEC 60601-1-2 

Anybus Wireless Bridge - Ethernet - Bluetooth Access Point

Anybus
 serial-bluetooth

Código: 024140

Anybus® Wireless Bridge Serial - Bluetooth is a rugged dual-mode Bluetooth (Bluetooth Smart Ready) serial-port adapter with Bluetooth low energy gateway functionality and u-blox Low Energy Serial Port Service. It allows connection for up to seven serial s
  • Eliminates the need for expensive or maintenance-heavy cabling
  • Connects up to 7 slaves with a serial RS-232/422/485 interface via Bluetooth
  • Includes Wireless Multidrop™ with simultaneous connections to both Bluetooth low energy and Classic Bluetooth devices
  • Extended Data Mode™ for separated multipoint data channels so that different data can be sent to or received from each slave
  • Features a Low Emission Mode®: Prevents disrupting other 2.4GHz radios
  • Effective range of up to 300m or 984ft
  • Easy configuration via push button or web interface
  • Advanced configuration with AT commands
  • Conforms to wireless standards used in Europe, USA, Canada and Japan
  • Rugged IP65 rated industrial design with choice of Antennas and accessories
Version Ethernet - Bluetooth Ethernet Access Point - Bluetooth Serial - Bluetooth
Dimensions  (L•W•H)91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"76 x 85 x 35mm 2,99 x 3,34 x 1,38"
Weight 120g or 0,26 lbs130g or 0,30 lbs 190g or 0,42 lbs
Operating temperature-30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F -30 to +85 °C -22 to +185 °F 
Output Power 13 dBm20 dBm 13 dBm
Power supply 9-30 VDC  9-30 VDC 8-30 VDC 
Power consumption min. 35mA at 30V (43mA average at 30V) min. 35mA at 30V (43mA average at 30V) min. 9mA at 30V (20mA average at 30V) 
Enclosure materialPlasticPlastic Metal
Mechanical rating IP65IP65IP65
MountingScrew holes for wall mountingScrew holes for wall mountingScrew holes for wall mounting
Max Range  300 meters 300 meters300 meters
Antenna/Connector Internal / NoExternal / Yes (RPSMA)External / Yes (RPSMA)
ConnectorsM12 (Ethernet and Power)M12 (Ethernet and Power) Male DSUB (Serial) Binder 712 (Power)
CERTIFICATIONS    
EuropeETSI R&TTE ETSI R&TTE ETSI R&TTE 
USA CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval
CanadaICC RSS ICC RSS ICC RSS 
JapanMIC - formerly TELEC MIC - formerly TELEC MIC - formerly TELEC
UL-Haz.Loc cUL Class 1 Div 2 cUL Class 1 Div 2-
Security Simple pairing Simple pairing WEP64, WEP128, WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP, EAP-TLS, 802.11i 
Medical Qualification --IEC 60601-1-2 

Anybus Wireless Bridge - Serial - Bluetooth

Anybus
 ethernet-wlan24

Código: 021440

Anybus® Wireless Bridge Ethernet - WLAN 2.4Ghz provides a proven wireless connection between Industrial Ethernet installations. It acts as a cable replacement gateway and is ideal for communication through hazardous areas, hard-to-reach locations or with
  • Use with point-to-point wireless Industrial Ethernet installations through hazardous or hard-to-reach locations
  • Eliminates the need for expensive or maintenance-heavy cabling
  • Bridges TCP/IP Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP and PROFINET
  • Uses WLAN 802.11 b,g,n communication standard with a throughput of up to 14 Mbps
  • Effective range of up to 400 meters
  • Easy configuration via push button or web interface
  • Advanced configuration with AT commands
  • Conforms to wireless standards used in Europe, USA, Canada and Japan
  • Rugged IP65 rated industrial design
Version Ethernet bridge via WLAN 2.4 GHz Ethernet bridge via WLAN 5 GHz Ethernet bridge via WLAN Dual-band (2.4/5 GHz) 
Dimensions  (L•W•H)91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"
Weight 120g or 0,26 lbs120g or 0,26 lbs 130g or 0,30 lbs
Operating temperature-30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F 
Output Power 20 dBm11 dBm 20 dBm
Power supply 9-30 VDC  9-30 VDC 9-30 VDC 
Power consumption min. 47mA at 30V (59mA average at 30V) min. 47mA at 30V (59mA average at 30V) min. 47mA at 30V (59mA average at 30V) 
Enclosure materialPlasticPlastic Plastic
Mechanical rating IP65IP65IP65
MountingScrew holes for wall mountingScrew holes for wall mountingScrew holes for wall mounting
Range  400 meters 200 meters400 meters
Antenna/Connector Internal / NoInternal / NoExternal / Yes (RPSMA)
ConnectorsM12 (Ethernet and Power)M12 (Ethernet and Power) M12 (Ethernet and Power)
CERTIFICATIONS    
EuropeETSI R&TTE ETSI R&TTE ETSI R&TTE 
USA CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval
CanadaICC RSS ICC RSS ICC RSS 
JapanMIC - formerly TELEC -2.4 Ghz only MIC - formerly TELEC
UL-Haz.Loc cUL Class 1 Div 2 cUL Class 1 Div 2cUL Class 1 Div 2
Security WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP

Anybus Wireless Bridge - Ethernet - WLAN 2.4 Ghz

Anybus
 ethernet-wlan5

Código: 021450

Anybus® Wireless Bridge Ethernet - WLAN 5 Ghz provides a proven wireless connection between Industrial Ethernet installations. It acts as a cable replacement gateway and is ideal for communication through hazardous areas, hard-to-reach locations or with m
  • Use with point-to-point wireless Industrial Ethernet installations through hazardous or hard-to-reach locations
  • Eliminates the need for expensive or maintenance-heavy cabling
  • Bridges TCP/IP Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP and PROFINET
  • Uses WLAN 802.11a/n communication standard with a throughput of up to 14 Mbps
  • Effective range of up to 200 meters
  • Easy configuration via push button or web interface
  • Advanced configuration with AT commands
  • Conforms to wireless standards used in Europe, USA, Canada and Japan
  • Rugged IP65 rated industrial design
Version Ethernet bridge via WLAN 2.4 GHz Ethernet bridge via WLAN 5 GHz Ethernet bridge via WLAN Dual-band (2.4/5 GHz) 
Dimensions  (L•W•H)91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"
Weight 120g or 0,26 lbs120g or 0,26 lbs 130g or 0,30 lbs
Operating temperature-30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F 
Output Power 20 dBm11 dBm 20 dBm
Power supply 9-30 VDC  9-30 VDC 9-30 VDC 
Power consumption min. 47mA at 30V (59mA average at 30V) min. 47mA at 30V (59mA average at 30V) min. 47mA at 30V (59mA average at 30V) 
Enclosure materialPlasticPlastic Plastic
Mechanical rating IP65IP65IP65
MountingScrew holes for wall mountingScrew holes for wall mountingScrew holes for wall mounting
Range  400 meters 200 meters400 meters
Antenna/Connector Internal / NoInternal / NoExternal / Yes (RPSMA)
ConnectorsM12 (Ethernet and Power)M12 (Ethernet and Power) M12 (Ethernet and Power)
CERTIFICATIONS    
EuropeETSI R&TTE ETSI R&TTE ETSI R&TTE 
USA CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval
CanadaICC RSS ICC RSS ICC RSS 
JapanMIC - formerly TELEC -2.4 Ghz only MIC - formerly TELEC
UL-Haz.Loc cUL Class 1 Div 2 cUL Class 1 Div 2cUL Class 1 Div 2
Security WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP

Anybus Wireless Bridge - Ethernet - WLAN 5 Ghz

Anybus
 ethernet-wlan-dualband

Código: 024120

Anybus® Wireless Bridge Ethernet - WLAN Dual Band 2.4/5 Ghz provides a proven wireless connection between Industrial Ethernet installations. It acts as a cable replacement gateway and is ideal for communication through hazardous areas, hard-to-reach locat
  • Use with point-to-point wireless Industrial Ethernet installations through hazardous or hard-to-reach locations
  • Eliminates the need for expensive or maintenance-heavy cabling
  • Uses Dual-band Wi-Fi 2.4/5 GHz to connect easier identify interference-free channels 
  • Uses WLAN 802.11a/b/g/n communication standard with a throughput of up to 14 Mbps
  • Effective range of up to 400 meters
  • External omnidirectional antenna means you do not need to align the units for optimal wireless connectivity
  • Easy configuration via push button or web interface
  • Advanced configuration with AT commands
  • Conforms to wireless standards used in Europe, USA, Canada and Japan
  • Rugged IP65 rated industrial design
Version Ethernet bridge via WLAN 2.4 GHz Ethernet bridge via WLAN 5 GHz Ethernet bridge via WLAN Dual-band (2.4/5 GHz) 
Dimensions  (L•W•H)91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"91 x 66 x 36.2mm 3,58 x 2,60 x 1,42"
Weight 120g or 0,26 lbs120g or 0,26 lbs 130g or 0,30 lbs
Operating temperature-30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F -30 to +65 °C -22 to +149 °F 
Output Power 20 dBm11 dBm 20 dBm
Power supply 9-30 VDC  9-30 VDC 9-30 VDC 
Power consumption min. 47mA at 30V (59mA average at 30V) min. 47mA at 30V (59mA average at 30V) min. 47mA at 30V (59mA average at 30V) 
Enclosure materialPlasticPlastic Plastic
Mechanical rating IP65IP65IP65
MountingScrew holes for wall mountingScrew holes for wall mountingScrew holes for wall mounting
Range  400 meters 200 meters400 meters
Antenna/Connector Internal / NoInternal / NoExternal / Yes (RPSMA)
ConnectorsM12 (Ethernet and Power)M12 (Ethernet and Power) M12 (Ethernet and Power)
CERTIFICATIONS    
EuropeETSI R&TTE ETSI R&TTE ETSI R&TTE 
USA CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval CC/CFR 47 part 15 unlicensed modular transmitter approval
CanadaICC RSS ICC RSS ICC RSS 
JapanMIC - formerly TELEC -2.4 Ghz only MIC - formerly TELEC
UL-Haz.Loc cUL Class 1 Div 2 cUL Class 1 Div 2cUL Class 1 Div 2
Security WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP WEP64, WEP128,WPAPSK, WPA2-PSK, TKIP, CCMP (AES), LEAP, PEAP

Anybus Wireless Bridge - Ethernet - WLAN Dual Band 2.4/5 Ghz

Anybus
 Anybus Wireless Bolt Mounting and Connector

Código: AWB2000

Anybus Wireless Bolt enables you to connect industrial machines and devices to a wireless network. It is attached onto a cabinet or a machine to enable wireless access over Bluetooth®, Bluetooth Low Energy® or WLAN (WiFi).
  • Configure or troubleshoot industrial machinery over a wireless network
  • Increase flexibility and mobility. Eliminate expensive fixed HMI’s by using a laptop, tablet or smartphone
  • Connect to moving field equipment such as an AGV’s (Automated Guided Vehicles)
  • Connect to a Cloud Service of your choice or get live data and integrate it into a SCADA system
  • Supports Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP, PROFINET, TCP/UDP
  • Unique method to handle interference disturbances without consequences to the Bluetooth conformity or the interoperability with other devices
  • Uses Dual-band Wi-Fi 2.4/5 GHz to connect easier and identify interference-free channels
  • All-in-one package: Connector, communication processor and integrated antenna in the same unit
  • Includes a configurable Digital Input to control e.g. roaming behavior. Max. 3m signal cable
  • Uses the ARM mbed 3.0 IoT Device Platform.
  • Simultaneous operation of Bluetooth and WLAN allowing for bridging and redundancy between the two networks
  • Security features for a secure industrial operation
Dimensions Diameter: 70 mm. Height: 70 mm (95 mm including connector. Outside height: 41 mm)
Weight 81g
TemperatureOperating: -40 to +65 °C  or -40 to +149 °F  - Storage: -40 to +85 °C  or -40 to +185 °F
Output Power WLAN 16 dBm - Bluetooth 10 dBm - Bluetooth Low Energy 7 dBm 
Power supply 9-30 VDC (-5% +20%), Cranking 12V (ISO 7637-2:2011 pulse 4). Reverse polarity protection.
Power consumption 0.7W idle, 1.7W max (54mA@24VDC with WLAN and 36mA@24VDC with Bluetooth)
Enclosure materialPlastic: PBT/PBT glass-reinforced/PC-ABS
Mechanical rating IP67 for top (outside the host), IP21 for bottom (inside the host)
MountingM50 screw and nut (50.5 mm hole needed)
Max Range  100 meters
Antenna Internal 
ConnectorIncluded plug connector (2x9p; 3.5mm, Phoenix DFMC 1.5/9-ST-3.5, push-in spring connection)
Vibration compatibilitySinosodial vibration test according to IEC 60068-2-6:2007 and with extra severities; Number of axes: 3 mutually perpendicular (X:Y:Z), Duration: 10 sweep cycles in each axes, Velocity: 1 oct/min, Mode: in operation, Frequency: 5-500 Hz, Displacement ±3.5 mm, Acceleration: 2g. Shock test according to IEC 60068-2-27:2008 and with extra severities; Wave shape: half sine, Number of shocks: ±3 in each axes, Mode: In operation, Axes ± X,Y,Z, Acceleration: 30 m/s2 , Duration: 11 ms. 
CERTIFICATIONS  
EuropeETSI R&TTE 
USA FCC/CFR 47 part 15 unlicensed modular transmitter approval 
CanadaICC RSS
JapanMIC (pending, pre-certified radio module)
South Korea NCC (pending, pre-certified radio module)
TaiwanKCC (pending, pre-certified radio module)
UL-Haz.Loc cUL Class 1 Div 2

Anybus Wireless Bolt - Ethernet

Anybus
 Anybus Wireless Bolt Mounting and Connector

Código: AWB2020

Anybus Wireless Bolt enables you to connect industrial machines and devices to a wireless network. It is attached onto a cabinet or a machine to enable wireless access over Bluetooth®, Bluetooth Low Energy® or WLAN (WiFi).
  • Configure or troubleshoot industrial machinery over a wireless network
  • Increase flexibility and mobility. Eliminate expensive fixed HMI’s by using a laptop, tablet or smartphone
  • Connect to moving field equipment such as an AGV’s (Automated Guided Veicles)
  • Connect to a Cloud Service of your choice or get live data and integrate it into a SCADA system
  • Support for CAN based devices and machines
  • Supports Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP, PROFINET, TCP/UDP
  • Unique method to handle interference disturbances without consequences to the Bluetooth conformity or the interoperability with other devices
  • Uses Dual-band Wi-Fi 2.4/5 GHz to connect easier and identify interference-free channels
  • All-in-one package: Connector, communication processor and integrated antenna in the same unit
  • Includes a configurable Digital Input to control e.g. roaming behavior. Max. 3m signal cable
  • Uses the ARM mbed 3.0 IoT Device Platform.
  • Simultaneous operation of Bluetooth and WLAN allowing for bridging and redundancy between the two networks
  • Security features for a secure industrial operation
Dimensions Diameter: 70 mm. Height: 70 mm (95 mm including connector. Outside height: 41 mm)
Weight 81g
TemperatureOperating: -40 to +65 °C  or -40 to +149 °F  - Storage: -40 to +85 °C  or -40 to +185 °F
Output Power WLAN 16 dBm - Bluetooth 10 dBm - Bluetooth Low Energy 7 dBm 
Power supply 9-30 VDC (-5% +20%), Cranking 12V (ISO 7637-2:2011 pulse 4). Reverse polarity protection.
Power consumption 0.7W idle, 1.7W max (54mA@24VDC with WLAN and 36mA@24VDC with Bluetooth)
Enclosure materialPlastic: PBT/PBT glass-reinforced/PC-ABS
Mechanical rating IP67 for top (outside the host), IP21 for bottom (inside the host)
MountingM50 screw and nut (50.5 mm hole needed)
Max Range  100 meters
Antenna Internal 
ConnectorIncluded plug connector (2x9p; 3.5mm, Phoenix DFMC 1.5/9-ST-3.5, push-in spring connection)
Vibration compatibilitySinosodial vibration test according to IEC 60068-2-6:2007 and with extra severities; Number of axes: 3 mutually perpendicular (X:Y:Z), Duration: 10 sweep cycles in each axes, Velocity: 1 oct/min, Mode: in operation, Frequency: 5-500 Hz, Displacement ±3.5 mm, Acceleration: 2g. Shock test according to IEC 60068-2-27:2008 and with extra severities; Wave shape: half sine, Number of shocks: ±3 in each axes, Mode: In operation, Axes ± X,Y,Z, Acceleration: 30 m/s2 , Duration: 11 ms. 
CERTIFICATIONS  
EuropeETSI R&TTE 
USA FCC/CFR 47 part 15 unlicensed modular transmitter approval 
CanadaICC RSS
JapanMIC (pending, pre-certified radio module)
South Korea NCC (pending, pre-certified radio module)
TaiwanKCC (pending, pre-certified radio module)
UL-Haz.Loc cUL Class 1 Div 2

Anybus Wireless Bolt - CAN and Ethernet

Anybus
 Anybus Wireless Bolt Mounting and Connector

Código: AWB2010

Anybus Wireless Bolt enables you to connect industrial machines and devices to a wireless network. It is attached onto a cabinet or a machine to enable wireless access over Bluetooth®, Bluetooth Low Energy® or WLAN (WiFi).
  • Configure or troubleshoot industrial machinery over a wireless network
  • Increase flexibility and mobility. Eliminate expensive fixed HMI’s by using a laptop, tablet or smartphone
  • Connect to moving field equipment such as an AGV’s (Automated Guided Veicles)
  • Connect to a Cloud Service of your choice or get live data and integrate it into a SCADA system
  • Connects serial RS-232/485 based devices and machines
  • Supports Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP, PROFINET, TCP/UDP
  • Unique method to handle interference disturbances without consequences to the Bluetooth conformity or the interoperability with other devices
  • Uses Dual-band Wi-Fi 2.4/5 GHz to connect easier and identify interference-free channels
  • All-in-one package: Connector, communication processor and integrated antenna in the same unit
  • Includes a configurable Digital Input to control e.g. roaming behavior. Max. 3m signal cable
  • Uses the ARM mbed 3.0 IoT Device Platform.
  • Simultaneous operation of Bluetooth and WLAN allowing for bridging and redundancy between the two networks
  • Security features for a secure industrial operation
Dimensions Diameter: 70 mm. Height: 70 mm (95 mm including connector. Outside height: 41 mm)
Weight 81g
TemperatureOperating: -40 to +65 °C  or -40 to +149 °F  - Storage: -40 to +85 °C  or -40 to +185 °F
Output Power WLAN 16 dBm - Bluetooth 10 dBm - Bluetooth Low Energy 7 dBm 
Power supply 9-30 VDC (-5% +20%), Cranking 12V (ISO 7637-2:2011 pulse 4). Reverse polarity protection.
Power consumption 0.7W idle, 1.7W max (54mA@24VDC with WLAN and 36mA@24VDC with Bluetooth)
Enclosure materialPlastic: PBT/PBT glass-reinforced/PC-ABS
Mechanical rating IP67 for top (outside the host), IP21 for bottom (inside the host)
MountingM50 screw and nut (50.5 mm hole needed)
Max Range  100 meters
Antenna Internal 
ConnectorIncluded plug connector (2x9p; 3.5mm, Phoenix DFMC 1.5/9-ST-3.5, push-in spring connection)
Vibration compatibilitySinosodial vibration test according to IEC 60068-2-6:2007 and with extra severities; Number of axes: 3 mutually perpendicular (X:Y:Z), Duration: 10 sweep cycles in each axes, Velocity: 1 oct/min, Mode: in operation, Frequency: 5-500 Hz, Displacement ±3.5 mm, Acceleration: 2g. Shock test according to IEC 60068-2-27:2008 and with extra severities; Wave shape: half sine, Number of shocks: ±3 in each axes, Mode: In operation, Axes ± X,Y,Z, Acceleration: 30 m/s2 , Duration: 11 ms. 
CERTIFICATIONS  
EuropeETSI R&TTE 
USA FCC/CFR 47 part 15 unlicensed modular transmitter approval 
CanadaICC RSS
JapanMIC (pending, pre-certified radio module)
South Korea NCC (pending, pre-certified radio module)
TaiwanKCC (pending, pre-certified radio module)
UL-Haz.Loc cUL Class 1 Div 2

Anybus Wireless Bolt - Serial RS-232/485 and Ethernet

Anybus
 Anybus Wireless bridge ii AWB3010 descripcion

Código: AWB3000

This second generation of the proven and trusted Wireless Bridge can communicate via both Bluetooth and WLAN and is ideal for communication through hazardous areas or hard-to-reach locations where cables are not desirable.
  • Use with point-to-point wireless Industrial Ethernet installations through hazardous or hard-to-reach locations
  • Use as an Access Point for up to seven clients
  • Eliminates the need for expensive or maintenance-heavy cabling
  • Bridges TCP/IP Ethernet and protocols such as: BACnet/IP, EtherNet/IP, Modbus-TCP and PROFINET
  • Unique method to handle interference disturbances
  • Effective range of up to 400 meters
  • Full compatibility with Anybus Wireless Bolt — a wireless product for machine mounting
  • Easy configuration via push button or web interface
  • Advanced configuration with AT commands
  • Simultaneous operation of Bluetooth and WLAN allowing for bridging and redundancy between the two networks
  • Conforms to wireless standards worldwide
  • Compatible with PROFIsafe requirements.
  • Rugged IP65 rated industrial design
  • Security features for a secure industrial operation
  • Starterkit available

Anybus Wireless Bridge II - Ethernet

Anybus
 Managed L3 Switch for Industrial Applications

Código: AWB5011

The intelligent Anybus Switches provide full Gigabit and ultra-high throughput. Multiple redundancy and cyber security features enable you to build a highly reliable and secure network.
  • FULL GIGABIT SWITCHING AND ULTRA-HIGH THROUGHPUT
  • 12-port Full Gigabit Ethernet with 8-port RJ 45 and 4-port SFP
  • 16k MAC address table
  • 1.5 MB packet buffer memory for H.264 burst
  • 9 kB jumbo frame
  • Store-and-forward with non-blocking switch fabric
  • DYNAMIC ROUTING WITH REDUNDANCY PROTECTION
  • RIPv1&v2, OSPFv1&v2 for intra-domain routing within an autonomous system
  • Efficient unicast/multicast static routing
  • VRRP for reliability and availability
  • ITU-T G.8032 V1/V2 ERPS RING REDUNDANCY
  • ITU standard Ring redundancy protocol
  • Provides sub-50ms protection and recovery switching for Ethernet traffic
  • Interoperability with most 3rd party industrial switches, providing fast recovery time
  • Efficient network interconnection and topology with ERPS Chain, multiple chains
  • CYBER SECURITY
  • L2-L7 IPv4/IPv6 Access Control List (ACL)
  • DHCP Snooping, IP Source Guard, Dynamic ARP Inspection
  • 802.1Q VLAN, Private VLAN, Advanced Port Security
  • Multi-Level user authentication
  • HTTPS/SSH/SFTP, 256-bit encryption
  • IEEE 802.1X port-based authentication
  • MAB for non-802.1X compliant end devices
  • RADIUS/TACACS+ centralized user authentication
  • RUGGED DESIGN
  • EN50121-4 for railway trackside applications
  • Top level EMC protection and excellent heat dissipation design for operating in -40 to 75oC environment
  • IEC 61000-6-2/4 Heavy Industrial Environment
  • MANAGEMENT FEATURES
  • Various configuration paths, including WebGUI, CLI, SNMP and RMON
  • IEEE 1588v1/v2 PTP time management
  • LLDP topology control
  • USB for backup/restore and firmware update
  • Software utility interface for LAN device management
  • NMS for individual component monitoring

Ethernet

     8 x 10/100/1000Base-T RJ-45

     4 x 100/1000Base SFP, DDM

Console

     1 x RS232 (RJ45) 115200.n.8.1

USB

     1 x USB type A

Operating Temp.

     -40°C-75°C , 0%-95% Non- Condensing

Data speeds

     1000Base-TX/FX

     100Base-TX/FX

     10Base-TX/FX

Power

     24 VDC (10-60 VDC)

     Max. 16.08W

     Support for dual power supplies

Weight

     1 380 g

Housing material

     Steel/aluminium

IP protection class

     IP31

Dimensions

     150 x 126.5 x 85.5 mm (without DIN rail clip)

Mounting

     DIN rail mount (bracket included)

Configuration

     CGI WebGUI, CLI, SNMP

 Security

     IEEE 802.1x/RADIUS, Private VLAN, ACL (MAC/IP filter) 

 Redundancy

     Rapid spanning tree protocol (RSTP)/Multiple spanning tree protocol
     (MSTP)
     ITU-T G.8032 v1/v2 Ethernet ring protection switching (ERPS)
     Virtual router redundancy protocol (VRRP)

 L3 Routing

     Static/dynamic IP routing, VLAN routing, RIP v1/v2, OSPF v1/v2, IGMP and Multicast routing

 Traffic Management

     Flow control, Port trunk/802.3ad LACP, VLAN, Private VLAN, GVRP, GMRP, QinQ, QoS, IGMP snooping v1/v2/v3, Rate control, Storm control, Port mirroring

 Network Management

     IPv4/IPv6, SNMP v1/v2c/v3, RMON, LLDP, DHCP server/client/Option 82, SysLog

Managed L3 Switch for Industrial Applications

Actualmente estamos trabajando en mostrarte los mejores resultados, si no encuentras el producto que buscas contacta con nosotros a través de info@er-soft.com o al número Tel. +34 916-408-408
Bienvenido a ER-Soft.
ER-Soft con la ley orgánica de protección de datos
Política de cookies.
Utilizamos cookies propias y de terceros para mejorar nuestros servicios y mostrarle publicidad relacionada con sus preferencias mediante el análisis de sus hábitos de navegación.
Si continúa navegando, consideramos que acepta su uso.
Más información pulsando aquí
X

¿Necesitas ayuda? Click

ayuda ER-Soft
X
Consulta a ER-Soft. *

 

*

 

* *Campos obligatorios.




*Al enviar el formulario consideramos que esta de acuerdo, con nuestra política de datos. Ver política de datos
X